# _lab
- u
user
02/23/2017, 1:03 PMThe skull canyon driver site one - u
user
02/23/2017, 1:04 PMYou have it the same specs in the vm as the skull canyon??? - u
user
02/23/2017, 1:04 PMFor cpu - u
user
02/23/2017, 1:04 PMActually it shouldn't matter - u
user
02/23/2017, 1:05 PMI think I used the Intel driver updated management software to do it - u
user
02/23/2017, 1:09 PMOk I'll try that, I think I got the one I have from the public site not the skull canyon site - u
user
02/23/2017, 1:09 PMJust email them. Note the “TIP” on this page. You’ll need to give them the Device ID of your existing unit. https://support.plex.tv/hc/en-us/articles/225877427-Supported-DVR-Devices-and-Antennas - u
user
02/23/2017, 1:09 PMIt’s not a trade in, just a discount - u
user
02/23/2017, 1:10 PMthey didn’t require my old one back (yet I’m not going to use it because I’m doing the plex thing) - u
user
02/23/2017, 1:13 PMThe new one works great, I got the EXTEND, it transcodes to h264 while the CONNECT streams raw mpeg2. EXTEND has the n wireless while CONNECT is ac. I always wire my device for obvious reasons. - u
user
02/23/2017, 1:16 PMYou using cable card or antenna? - u
user
02/23/2017, 1:38 PMGot to tell you @User this is making me seriously hate XenServer 😉. So here's what happens... I have it fully patched, XS tools installed. I assign the VGPU and boot. It's slower but not terrible. I can log in and see the display adapter. For about 30 seconds it is using the Windows default display driver. If I try and run the install of the Intel graphics I get that message that it doesn't meet the requirements. After about 30-45 seconds it does a hardware update and shows the Intel display adapter, and then... it hard reboots. Once it's back up I try and log in and just have a black screen and CPU is pegged back at 100%. - u
user
02/23/2017, 1:43 PMHmm I have never seen that sequence happen in any of my setups - u
user
02/23/2017, 1:44 PMI have 30 of these running right now globally - u
user
02/23/2017, 1:44 PMI assuming this is windows 10? - u
user
02/23/2017, 1:45 PMYep win 10 enterprise - u
user
02/23/2017, 1:46 PMI will build one in the morning a write up my exact steps for you - u
user
02/23/2017, 1:46 PMI am wondering if it's because I install the VDA - u
user
02/23/2017, 1:47 PMHdx3D mode - u
user
02/23/2017, 1:47 PMHas to be it - u
user
02/23/2017, 1:48 PMOS, XSTools, Domain Join, VDA HDX3D, add gpu, install Intel drivers - u
user
02/23/2017, 1:48 PMTrying to find my notes on it - u
user
02/23/2017, 1:54 PMAhhh - u
user
02/23/2017, 1:54 PMOk yes I was NOT doing the VDA yet - u
user
02/23/2017, 1:54 PMOk, I will try that order 🙂 Luckily I used a snapshot this time. - u
user
02/23/2017, 2:23 PMNope. Exact same behavior. - u
user
02/23/2017, 2:27 PMHmm - u
user
02/23/2017, 2:28 PMLet me build one in about 5 hours and report back - u
user
02/23/2017, 2:33 PMThanks. Only reason I got the Skull Canyon was to try the Iris Pro, so got to figure this out. I may try and update to 7.1 also to see if that helps. - u
user
02/23/2017, 2:36 PMI have it on 7 haven't gone to 7.1 yet so I know it works